Plumbing Basics: Your Starting Point for Bathtub Installation
Plumbing Basics: Your Starting Point for Bathtub Installation
Blog Article
Everyone will have their own unique opinions involving How to Install a Bathtub Yourself.
Setting up a tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably tough job. If the old tub is conveniently accessible, the project can relocate immediately; if you have to open a wall surface to get rid of the old bathtub and place the new bath tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to leave the old tub as well as set in the new one. Ensure you have actually certified yourself for the job and also fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to think about employing one before you start. Opportunities are you may require an expert plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your shower room if you have actually already gotten a brand-new bathtub and don't need to change the plan of your previous water system pipes.
Your tools as well as material list need to comprise the following:
Planning for the Setup
First of all, the sustaining framework provided with the bath should be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The process of eliminating the existing faucets can be rather troublesome due to the restricted gain access to that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before going on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of the two wood boards under its feet, place the bathtub in the called for position. The wooden boards are practical in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small points.
The next objective is to ensure that the tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bath tub up until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap port to the proper supply pipeline by making a compression join; after that do the exact same for the other tap.
Switch on the water supply as well as inspect all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub and likewise check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bathtub should wait till the bathtub has been made use of at the very least when as this will certainly resolve it right into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers are in area in between the tap as well as the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous kind should be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall surface between the bath as well as the tiling, causing issues with wetness and possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to allow for the activity experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very inquisitive about Tools You Need to Install a New Bathtub and I really hope you liked the entire piece. Sharing is good. Helping people is fun. I take joy in reading our article about A Step-by-Step Guide to Installing a Bathtub.
We've got this! Report this page